Azuro 2.5 kW – heat pump for inflatable and prefab pools up to 11 m³

658,00 €

  • Azuro 2.5 kW heat pump for inflatable and prefab pools up to 11 m³
  • Titanium heat exchanger and LCD display with sensors
  • Heats with up to four times less electricity than an electric heater
  • 32/38 mm and Ø 50 mm connections

Frequently bought together

Total for selected:

Description

This heat pump from the Azuro series is designed to warm the water in inflatable and prefab pools with a volume of up to 11 m³. It draws heat from the surrounding air, so power consumption is up to four times lower than with an electric heater. The unit features an LCD display, temperature and pressure sensors and a titanium heat exchanger.

The model at a glance

  • Heat output: 2.5 kW at 20 °C, with an operating power of 0.59 kW.
  • Suitable volume: pools up to 11 m³.
  • Technology: standard, non-inverter.
  • Control: LCD display with temperature and pressure sensors.
  • Heat exchanger: titanium.
  • Connection: 2 pre-fitted hose connectors, 32/38 mm.

How the heat pump works

The pump draws in the surrounding air and uses the heat it contains. The energy is passed to the refrigerant circuit, in which the medium expands and condenses, and the heat is multiplied many times over before it is released into the water. It works best when the air temperature is between 15 and 25 °C. Below 15 °C the coefficient of performance drops sharply. In spring and autumn the swimming season is almost doubled, and with covered pools the effect is even greater.

The picture illustrating the principle of operation is for illustration only – the values in it are examples and do not belong to this model.

Connection and installation

The unit arrives fully assembled. To put it into operation, simply connect it to the pool filter system. The water inlet and outlet are designed for pipes with a diameter of 50 mm. If your installation uses corrugated hoses of 32 or 38 mm, you will need to add two adapters from Ø50 to Ø32–38 mm. A sand filter with a capacity of at least 2.8 m³/h is required for the pool.

Important for safety: the heat pump, the filter pump and any other electrical equipment must be placed at least 3.5 m from the pool wall. The electrical circuit must be protected by a residual current device (RCD) of up to 30 mA. Before installation, check the condition of your installation and read the manual.

Technical specifications

Manufacturer and seriesMountfield (Czech Republic), Azuro
Suitable poolsinflatable and prefab, up to 11 m³
Heat output2.5 kW (measured at 20 °C)
Power consumption0.59 kW
COP4.2 at 28 °C
Heat exchangertitanium
Typestandard, non-inverter
Water flow2.0 m³/h
Operating noise48 dB (A)
Automatic defrost functionnot available
Voltage230/50 V/Hz
DisplayLCD
Unit dimensions (L/W/H)31/36/38
Weight net / packed18 kg / 20 kg
Package dimensions38 × 45 × 45 cm
Connectionhose connectors 32/38 mm; pipes Ø 50 mm
Filter requirementsand filter, from 2.8 m³/h upwards

Frequently asked questions

Is it suitable for a large pool?

No. The model is designed for inflatable and prefab pools up to 11 m³.

Is this pump an inverter model?

No, it is a standard non-inverter heat pump.

Does it have automatic defrosting?

No, this function is not provided.

What pipes can be connected?

The inlet and outlet are for Ø 50 mm pipes; the set includes two pre-fitted 32/38 mm hose connectors. If your hoses are 32 or 38 mm, two adapters are added.

At what temperatures are the best results achieved?

With air between 15 and 25 °C. Below 15 °C the heat output drops noticeably.

See also: Wellness, Pools and Equipment, Water Heating, Pools, Pool Chemicals, Pool Accessories.

You may also like

More from Mountfield

Newsletter

News, promotions and ideas for home and garden

Subscribe to our newsletter to receive news about promotions, new products and other useful information.